[Prism54-users] cell 00

[Johannes Zellner]

On Fri, Dec 05, 2003 at 11:39:30AM +0100, Istvan Turk wrote:
> 
> i have same distro, same card and same problem with the latest driver!
> i can't find any solution yet :(
> 
> but 20031128 snapshot with 2.6-test11 kernel works for me!

here it doesn't!

# ifup eth2
Error for wireless request "Set ESSID" (8B1A) :
    SET failed on device eth2 ; Connection timed out.

so the prism54 module from the current cvs at least allows me to bring
the interface up and configure ESSID and KEY.


> 
> cheers,
> mosquito
> 
> Johannes Zellner wrote:
> >Hi,
> >
> >with kernel 2.6.0-test11 and the latest prism54 from CVS I can bring up
> >my SMC2802, but it shows
> >
> >    # iwconfig eth2
> >    eth2      PRISM Duette/GT  ESSID:"my essid"  
> >              Mode:Ad-Hoc  Channel:6  Cell: 00:00:00:00:00:00  
> >              Sensitivity=0  
> >              Retry min limit:0   RTS thr=0 B   Fragment thr=0 B   
> >              Encryption key:FFFF-FFFF-FFFF-FFFF-FFFF-FFFF-FF   Security 
> >              mode:restricted
> >              Link Quality:0  Signal level:0  Noise level:0
> >              Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
> >              Tx excessive retries:0  Invalid misc:0   Missed beacon:0
> >
> >so it seems that Cell == 00.. is wrong. I'm running debian unstable with
> >the appropriate packages (hotplug / iwconfig) installed. The card worked
> >with 2.6.0-test10 and the prism54 driver of about 2 - 3 weeks ago. After
> >bringing up the driver, dmesg shows:
> >
> >    # dmesg
> >    Loaded prism54 driver, version 1.0.2.2
> >    eth2: uploading firmware...
> >    eth2: firmware uploaded done, now triggering reset...
> >    eth2: prism54_mib_init()
> >    eth2: islpci_open()
> >    eth2: resetting device...
> >    eth2: uploading firmware...
> >
> >for completeness, here is what lspci shows:
> >
> >    # lspci -vv
> >    00:09.0 Network controller: Harris Semiconductor D-Links DWL-g650 A1 
> >    (rev 01)
> >            Subsystem: Standard Microsystems Corp [SMC]: Unknown device 
> >            2802
> >            Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
> >            ParErr- Stepping- SERR- FastB2B-
> >            Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium 
> >            >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> >            Latency: 80 (2500ns min, 7000ns max), Cache Line Size: 0x08 
> >            (32 bytes)
> >            Interrupt: pin A routed to IRQ 5
> >            Region 0: Memory at e2000000 (32-bit, non-prefetchable) 
> >            [size=8K]
> >            Capabilities: [dc] Power Management version 1
> >                    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
> >                    PME(D0+,D1+,D2+,D3hot+,D3cold+)
> >                    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> >
> >I've ACPI turned OFF!
> >Would be nice, if I could get the card functional again ;-)
> >
> _______________________________________________
> Prism54-users mailing list
> Prism54-users@prism54.org
> http://prism54.org/mailman/listinfo/prism54-users

-- 
Johannes